Farmers make money from waste

23 February 2010

Farmers are using CC-Link fieldbus control to generate power from biogas extracted from slurry. The biogas is sent to fuel cogeneration plants and is ultimately used to heat buildings, power machinery or export it to the grid.

The systems must run reliably for years if they are to repay their initial investment and provide a stable power supply to the end-users.

German power plant specialists Dreyer & Bosse provides autonomous cogeneration units that use CC-Link open fieldbus network technology for data communications and crucial safety and monitoring functions.

Biogas-fuelled power plants turn liquid manure, plant waste and special fuel crops into energy. The main component is a heat and power cogeneration unit that generates power and heat from biogas, which is the primary output of the biomass fermentation unit.

In Germany, operators of plants that generate electricity from renewable energy sources are paid guaranteed rates for the power they feed into the public grid, and they can also feed the heat produced into a local district heating network. British farms tend to be about the same size as German ones, and there is much interest in developing the idea. The industrial scale farms of America’s mid-western states are opting for bigger plants, while the smaller family-owned farms of France, Spain and the Mediterranean countries are adapting the concept for their circumstances.

Dreyer & Bosse builds custom-designed cogeneration units based on individual selection of standard components. Usually the generators are driven by biogas with dual-fuel diesel/biogas engines for back up to ensure reliability and availability. Everything is installed in a single container that is delivered ready for connection.

Modern control technology and the CC-Link (Control and Communication Link) fieldbus network are designed to ensure that the plants are both reliable and economical to operate.

A D&B system could, for example, consist of a 500-kilowatt cogeneration unit installed on a farm with 70 hectares (173 acres) of arable land and 5 hectares (12.5 acres) of pastures. The slurry will be a mixture of straw and manure.

The entire system is controlled by a powerful compact controller from Mitsubishi Electric, supported by two smaller controllers from the same manufacturer. The main controller is a MELSEC FX3U programmable logic controller (PLC), which communicates with the system’s various automation components via a CC-Link master module and standard serial ports. Integrated instructions and drivers for Mitsubishi automation components eliminate the need for complex and time-consuming controller programming.

Components include a graphical control panel for clear visualisation of all processes. This makes operation as easy as possible for the farmer, who is likely to be fairly non-technical. As a back up an industrial modem will provide remote access so that service engineers will be able to interrogate the plant without actually having to visit remote farms. Another critical component is the frequency inverter that powers and regulates the engine cooling system and the gas compressor on the two gas-fuelled engines.

A number of important system safety and monitoring functions are performed by air circuit breakers with CC-Link interfaces. These advanced switchgear components protect the generators against peak overloads, short circuits and power failures and also handle the automatic network synchronisation with the public power grid. The fast-switching circuit breakers of Mitsubishi Electric’s Super AE series act as the link between the gas engine and generator set of the cogeneration unit and the public power grid. The tripping characteristics of the circuit breaker’s electronic generator protection module are configured for the connected generator system with a series of switches. Network synchronisation includes support for electrical remote control and is effected with an undervoltage tripping device in the circuit breaker combined with an integrated motor drive.

The circuit breakers electronic trip relay is connected to the central controller via the CC-Link network. The measurement circuits integrated in the trip relay can monitor and analyse all the relevant generator parameters. For example, the system can check the current voltage, current and power levels in the low-voltage network and send them to the controller and the control panel. Intelligent modern circuit breakers like the Super AE series can handle these functions themselves because they have integrated network support and digital instrumentation modules; in older systems these features aren’t possible without connecting additional transformers, power transducers and a number of analogue-digital converters with the controller. The circuit breaker can also be switched on and off remotely via the CC-Link network, with the help of a peripheral I/O module with digital inputs and outputs. The digital inputs are configured as relay contacts and dimensioned to handle the currents of the circuit breaker’s closing coil, shunt trip device and drive motor.

Simple bus wiring
The CC-Link fieldbus network and the simple installation of the system components enabled the Dreyer & Bosse engineers to reduce both material costs and wiring overheads. Resistance to electromagnetic interference was also a major factor for the choice of this technology. Unlike most other fieldbus systems, the conformity tests for CC-Link compatible devices include comprehensive electromagnetic compatibility (EMC) tests, in addition to all the standard tests for things like proper functioning, ageing performance and resistance to damp.

CC-Link’s high network data transfer rates of up to 10 megabits per second and its deterministic performance ensure a continuous update cycle speed of just 3.9 milliseconds for all data. The network is configured with simple menus in the PLC programming software package, which conforms to the international IEC 61131-3 standard. No special device configuration files need to be created to set up the network: the parameters are read directly from the CC-Link master module by the PLC program using a standard function block. The PLC’s processing speed matches the network transfer rates, making it possible to achieve the high levels of safety and reliability required for cogeneration plants, for example for feeding the generated power into the public grid.

All the electrical parameters of the low-voltage network can be displayed in detail on the system’s clear graphical control panel. When a circuit breaker trips a message is triggered automatically and the operator gets detailed information from the trip relay that has activated via the CC-Link network. The last ten alarms and trip messages are also stored in an error buffer with timestamps for later analysis. Remote maintenance and remote monitoring of important parameters via modem are also supported.

Contact Details and Archive...

Related Articles...

Additional Information...

Print this page | E-mail this page